If request_irq failed, we would pass wrong arguments to
dma_free_coherent. https://bugzilla.redhat.com/show_bug.cgi?id=728185
Reported-by: Mads Kiilerich
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Clemens points out that we need to use compat_ptr() in order to safely
cast from u64 to addresses of a 32-bit usermode client.
Before, our conversion went wrong
- in practice if the client cast from pointer to integer such that
sign-extension happened, (libraw1394 and libdc1394 at least were not
doing that, IOW were not affected)
or
- in theory on s390 (which doesn't have FireWire though) and on the
tile architecture, regardless of what the client does.
The bug would usually be observed as the initial get_info ioctl failing
with "Bad address" (EFAULT).
Reported-by: Carl Karsten <carl@personnelware.com>
Reported-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Between open(2) of a /dev/fw* and the first FW_CDEV_IOC_GET_INFO
ioctl(2) on it, the kernel already queues FW_CDEV_EVENT_BUS_RESET events
to be read(2) by the client. The get_info ioctl is practically always
issued right away after open, hence this condition only occurs if the
client opens during a bus reset, especially during a rapid series of bus
resets.
The problem with this condition is twofold:
- These bus reset events carry the (as yet undocumented) @closure
value of 0. But it is not the kernel's place to choose closures;
they are privat to the client. E.g., this 0 value forced from the
kernel makes it unsafe for clients to dereference it as a pointer to
a closure object without NULL pointer check.
- It is impossible for clients to determine the relative order of bus
reset events from get_info ioctl(2) versus those from read(2),
except in one way: By comparison of closure values. Again, such a
procedure imposes complexity on clients and reduces freedom in use
of the bus reset closure.
So, change the ABI to suppress queuing of bus reset events before the
first FW_CDEV_IOC_GET_INFO ioctl was issued by the client.
Note, this ABI change cannot be version-controlled. The kernel cannot
distinguish old from new clients before the first FW_CDEV_IOC_GET_INFO
ioctl.
We will try to back-merge this change into currently maintained stable/
longterm series, and we only document the new behaviour. The old
behavior is now considered a kernel bug, which it basically is.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: <stable@kernel.org>
On Jun 27 Linus Torvalds wrote:
> The correct error code for "I don't understand this ioctl" is ENOTTY.
> The naming may be odd, but you should think of that error value as a
> "unrecognized ioctl number, you're feeding me random numbers that I
> don't understand and I assume for historical reasons that you tried to
> do some tty operation on me".
[...]
> The EINVAL thing goes way back, and is a disaster. It predates Linux
> itself, as far as I can tell. You'll find lots of man-pages that have
> this line in it:
>
> EINVAL Request or argp is not valid.
>
> and it shows up in POSIX etc. And sadly, it generally shows up
> _before_ the line that says
>
> ENOTTY The specified request does not apply to the kind of object
> that the descriptor d references.
>
> so a lot of people get to the EINVAL, and never even notice the ENOTTY.
[...]
> At least glibc (and hopefully other C libraries) use a _string_ that
> makes much more sense: strerror(ENOTTY) is "Inappropriate ioctl for
> device"
So let's correct this in the <linux/firewire-cdev.h> ABI while it is
still young, relative to distributor adoption.
Side note: We return -ENOTTY not only on _IOC_TYPE or _IOC_NR mismatch,
but also on _IOC_SIZE mismatch. An ioctl with an unsupported size of
argument structure can be seen as an unsupported version of that ioctl.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: <stable@kernel.org>
The software reset in firewire-ohci's pci_remove does not have a great
prospect of success if the card was already physically removed at this
point. So let's skip the 500 ms that were spent in retries here.
Also, replace a defined constant by its open-coded value. This is not a
constant from a specification but an arbitrarily chosen retry limit. It
was only used in this single place.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Detect and handle ejection of FireWire CardBus cards in PHY register
accesses:
- The last attempt of firewire-core to reset the bus during shutdown
caused a spurious "firewire_ohci: failed to write phy reg" error
message in the log. Skip this message as well as the prior retry
loop that needlessly took 100 milliseconds.
- In the unlikely case that a PHY register was read right after card
ejection, a bogus value was obtained and possibly acted upon.
Instead, fail the read attempt.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Stopping an isochronous reception DMA context takes two loop iterations
in context_stop on several controllers (JMicron, NEC, VIA). But there
is no extra delay necessary between these two reg_read trials; the MMIO
reads themselves are slow enough. Hence bring back the behavior from
before commit dd6254e5c0 "firewire: ohci:
remove superfluous posted write flushes" on these controllers by means
of an "if (i)" condition.
Isochronous context stop is performed in preemptible contexts (and only
rarely), hence this change is of little impact. (Besides, Agere and TI
controllers always, or almost always, have the context stopped already
at the first ContextControl read.)
More important is asynchronous transmit context stop, which is performed
while local interrupts are disabled (on the two AT DMAs in
bus_reset_tasklet, i.e. after a self-ID-complete event). In my
experience with several controllers, tested with a usermode AT-request
transmitter as well as with FTP transmission over firewire-net, the AT
contexts were luckily already stopped at the first ContextControl read,
i.e. never required another MMIO read let alone mdelay. A possible
explanation for this is that the controllers which I tested perhaps stop
AT DMA before they perform the self-ID reception DMA.
But we cannot be sure about that and should keep the interrupts-disabled
busy loop as short as possible. Hence, query the ContextControl
register in 1000 udelay(10) intervals instead of 10 udelay(1000)
intervals. I understand from an estimation by Clemens Ladisch that
stopping a busy DMA context should take microseconds or at worst tens of
microseconds, not milliseconds.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
The call to flush_writes() in context_stop() is superfluous because
another register read is done immediately afterwards.
The call to flush_writes() in ar_context_run() does not need to be done
individually for each AR context, so move it to ohci_enable(). This
also makes ohci_enable() clearer because it no longer depends on a side
effect of ar_context_run() to flush its own register writes.
Finally, the setting of a context's wake bit does not need to be flushed
because neither the driver logic nor the API require the CPU to wait for
this action. This removes the last MMIO reads from the packet queueing
code paths.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Fixing a deprecation, replacing __attribute__((packed)) with __packed.
It was deprecated for portability, specifically to avoid GCC specific
code. See commit 82ddcb0405.
Signed-off-by: August Lilleaas <august@augustl.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (added include compiler.h)
The struct sbp2_logical_unit.work items can all be executed in parallel
but are not reentrant. Furthermore, reconnect or re-login work must be
executed in a WQ_MEM_RECLAIM workqueue.
Hence replace the old single-threaded firewire-sbp2 workqueue by a
concurrency-managed but non-reentrant workqueue with rescuer.
firewire-core already maintains one, hence use this one.
In earlier versions of this change, I observed occasional failures of
parallel INQUIRY to an Initio INIC-2430 FireWire 800 to dual IDE bridge.
More testing indicates that parallel INQUIRY is not actually a problem,
but too quick successions of logout and login + INQUIRY, e.g. a quick
sequence of cable plugout and plugin, can result in failed INQUIRY.
This does not seem to be something that should or could be addressed by
serialization.
Another dual-LU device to which I currently have access to, an
OXUF924DSB FireWire 800 to dual SATA bridge with firmware from MacPower,
has been successfully tested with this too.
This change is beneficial to environments with two or more FireWire
storage devices, especially if they are located on the same bus.
Management tasks that should be performed as soon and as quickly as
possible, especially reconnect, are no longer held up by tasks on other
devices that may take a long time, especially login with INQUIRY and sd
or sr driver probe.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
We do not need slab allocations for ORB pointer write transactions
anymore in order to satisfy streaming DMA mapping constraints, thanks to
commit da28947e7e "firewire: ohci: avoid separate DMA mapping for
small AT payloads".
(Besides, the slab-allocated buffers that firewire-sbp2 used to provide
for 8-byte write requests were still not fully portable since they
shared a cacheline with unrelated CPU-accessed data.)
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
firewire-sbp2 already takes care for internal serialization where
required (ORB list accesses), and it does not use cmd->serial_number
internally. Hence it is safe to not grab the shost lock around
queuecommand.
While we are at housekeeping, drop a redundant struct member:
sbp2_command_orb.done is set once in a hot path and dereferenced once in
a hot path. We can as well dereference sbp2_command_orb.cmd->scsi_done
instead.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
firewire-core manages the following types of work items:
fw_card.br_work:
- resets the bus on a card and possibly sends a PHY packet before that
- does not sleep for long or not at all
- is scheduled via fw_schedule_bus_reset() by
- firewire-ohci's pci_probe method
- firewire-ohci's set_config_rom method, called by kernelspace
protocol drivers and userspace drivers which add/remove
Configuration ROM descriptors
- userspace drivers which use the bus reset ioctl
- itself if the last reset happened less than 2 seconds ago
fw_card.bm_work:
- performs bus management duties
- usually does not (but may in corner cases) sleep for long
- is scheduled via fw_schedule_bm_work() by
- firewire-ohci's self-ID-complete IRQ handler tasklet
- firewire-core's fw_device.work instances whenever the root node
device was (successfully or unsuccessfully) discovered,
refreshed, or rediscovered
- itself in case of resource allocation failures or in order to
obey the 125ms bus manager arbitration interval
fw_device.work:
- performs node probe, update, shutdown, revival, removal; including
kernel driver probe, update, shutdown and bus reset notification to
userspace drivers
- usually sleeps moderately long, in corner cases very long
- is scheduled by
- firewire-ohci's self-ID-complete IRQ handler tasklet via the
core's fw_node_event
- firewire-ohci's pci_remove method via core's fw_destroy_nodes/
fw_node_event
- itself during retries, e.g. while a node is powering up
iso_resource.work:
- accesses registers at the Isochronous Resource Manager node
- usually does not (but may in corner cases) sleep for long
- is scheduled via schedule_iso_resource() by
- the owning userspace driver at addition and removal of the
resource
- firewire-core's fw_device.work instances after bus reset
- itself in case of resource allocation if necessary to obey the
1000ms reallocation period after bus reset
fw_card.br_work instances should not, and instances of the others must
not, be executed in parallel by multiple CPUs -- but were not protected
against that. Hence allocate a non-reentrant workqueue for them.
fw_device.work may be used in the memory reclaim path in case of SBP-2
device updates. Hence we need a workqueue with rescuer and cannot use
system_nrt_wq.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Reviewed-by: Tejun Heo <tj@kernel.org>
When queueing iso packets, the run time is dominated by the two
MMIO accesses that set the DMA context's wake bit. Because most
drivers submit packets in batches, we can save much time by
removing all but the last wakeup.
The internal kernel API is changed to require a call to
fw_iso_context_queue_flush() after a batch of queued packets.
The user space API does not change, so one call to
FW_CDEV_IOC_QUEUE_ISO must specify multiple packets to take
advantage of this optimization.
In my measurements, this patch reduces the time needed to queue
fifty skip packets from userspace to one sixth on a 2.5 GHz CPU,
or to one third at 800 MHz.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
We do not need slab allocations anymore in order to satisfy
streaming DMA mapping constraints, thanks to commit da28947e7e
"firewire: ohci: avoid separate DMA mapping for small AT payloads".
(Besides, the slab-allocated buffers that firewire-core, firewire-sbp2,
and firedtv used to provide for 8-byte write and lock requests were
still not fully portable since they crossed cacheline boundaries or
shared a cacheline with unrelated CPU-accessed data. snd-firewire-lib
got this aspect right by using an extra kmalloc/ kfree just for the
8-byte transaction buffer.)
This change replaces kmalloc'ed lock transaction scratch buffers in
firewire-core, firedtv, and snd-firewire-lib by local stack allocations.
Perhaps the most notable result of the change is simpler locking because
there is no need to serialize usages of preallocated per-device buffers
anymore. Also, allocations and deallocations are simpler.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Current implementation of ohci_set_config_rom() uses a deferred
bus reset via fw_schedule_bus_reset(). If clients add multiple
unit descriptors to the config_rom in quick succession, the
deferred bus reset may not have fired before succeeding update
requests have come in. This can lead to an incorrect partial
update of the config_rom for both addition and removal of
config_rom descriptors, as the ohci_set_config_rom() routine
will return -EBUSY if a previous pending update has not been
completed yet; the requested update just gets dropped on the floor.
This patch recognizes that the "in-flight" update can be modified
until it has been processed by the bus-reset, and the locking
in the bus_reset_tasklet ensures that the update is done atomically
with respect to modifications made by ohci_set_config_rom(). The
-EBUSY error case is simply removed.
[Stefan R: The bug always existed at least theoretically. But it
became easy to trigger since 2.6.36 commit 02d37bed18 "firewire: core:
integrate software-forced bus resets with bus management" which
introduced long mandatory delays between janitorial bus resets.]
Signed-off-by: Benjamin Buchalter <bj@mhlabs.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (trivial style changes)
Cc: <stable@kernel.org> # 2.6.36.y and newer
When z==2, the condition "key == 2" is superfluous because it cannot
occur without "b == 3", as a descriptor with b!=3 and key==2 would be
an OUTPUT_MORE_IMMEDIATE descriptor which cannot be used alone.
Also remove magic numbers and needless computations on the b field.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
For AT packet payloads of up to eight bytes, we have enough unused space
in the DMA descriptors list so that we can put a copy of the payload
there and thus avoid having to create a separate streaming DMA mapping
for the payload buffer.
In a CPU-bound microbenchmark that just sends 8-byte packets, bandwidth
was measured to increase by 5.7 %, from 1009 KB/s to 1067 KB/s. In
practice, the only performance-sensitive usage of small asynchronous
packets is the SBP-2 driver's write to the ORB_POINTER register during
SCSI command submission.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
OHCI 1.1 5.7.3 not only forbids enabling or starting any DMA contexts
before the linkEnable bit is set, but also explicitly warns of undefined
behaviour if this order is violated.
Don't violate it then.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
firewire: core: ignore link-active bit of new nodes, fix device recognition
firewire: sbp2: revert obsolete 'fix stall with "Unsolicited response"'
firewire: core: increase default SPLIT_TIMEOUT value
firewire: ohci: Misleading kfree in ohci.c::pci_probe/remove
firewire: ohci: omit IntEvent.busReset check rom AT queueing
firewire: ohci: prevent starting of iso contexts with empty queue
firewire: ohci: prevent iso completion callbacks after context stop
firewire: core: rename some variables
firewire: nosy: should work on Power Mac G4 PCI too
firewire: core: fix card->reset_jiffies overflow
firewire: cdev: remove unneeded reference
firewire: cdev: always wait for outbound transactions to complete
firewire: cdev: remove unneeded idr_find() from complete_transaction()
firewire: ohci: log dead DMA contexts
Like the older ieee1394 core driver, firewire-core skipped scanning of
any new node whose PHY sent a self ID without "link active" bit. If a
device had this bit off mistakenly, it meant that it was inaccessible to
kernel drivers with the old IEEE 1394 driver stack but could still be
accessed by userspace drivers through the raw1394 interface.
But with firewire-core, userspace drivers don't get to see such buggy
devices anymore. This is effectively a driver regression since this
device bug is otherwise harmless.
We now attempt to scan all devices, even repeaters that don't have a
link or powered-down devices that have everything but their PHY shut
down when plugged in. This results in futile repeated scanning attempts
in case of such devices that really don't have an active link, but this
doesn't hurt since recent workqueue infrastructure lets us run more
concurrent scanning jobs than we can shake a stick at.
This should fix accessibility of Focusrite Saffire PRO 26 I/O:
http://sourceforge.net/mailarchive/forum.php?thread_name=20110314215622.5c751bb0%40stein&forum_name=ffado-user
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Now that firewire-core sets the local node's SPLIT_TIMEOUT to 2 seconds
per default, commit a481e97d3c is no
longer required.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
The SPLIT_TIMEOUT mechanism is intended to detect requests that somehow
got lost. However, when the timeout value is too low, transactions that
could have been completed successfully will be cancelled. Furthermore,
there are chips whose firmwares ignore the configured split timeout and
send late split response; known examples are the DM1x00 (BeBoB), TCD22x0
(DICE), and some OXUF936QSE firmwares.
This patch changes the default timeout to two seconds, which happens to
be the default on other OSes, too.
Actual lost requests are extremely rare, so there should be no practical
downside to increasing the split timeout even on devices that work
correctly.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Add a driver for two playback-only FireWire devices based on the OXFW970
chip.
v2: better AMDTP API abstraction; fix fw_unit leak; small fixes
v3: cache the iPCR value
v4: FireWave constraints; fix fw_device reference counting;
fix PCR caching; small changes and fixes
v5: volume/mute support; fix crashing due to pcm stop races
v6: fix build; one-channel volume for LaCie
v7: use signed values to make volume (range checks) work; fix function
block IDs for volume/mute; always use channel 0 for LaCie volume
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Acked-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Tested-by: Jay Fenlason <fenlason@redhat.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It seems drivers/firewire/ohci.c is making some optimistic assumptions
about struct fw_ohci and that member "card" will always remain the first
member of the struct.
Plus it's probably going to confuse a lot of static code analyzers too.
So I wonder if there is a good reason not to free the ohci struct just
like it was allocated instead of the tricky &ohci->card way?
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
It is perhaps just a rudiment from before mainline submission of the
driver.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Since commit 82b662dc41 "flush AT contexts after bus reset for OHCI 1.2",
the driver takes care of any AT packets that were enqueued during a bus
reset phase. The check from commit 76f73ca1b2 is therefore no longer
necessary and the MMIO read can be avoided.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
If a misguided program tried to start an isochronous context before it
has queued any packets, the call would appear to succeed, but the
context would not actually go into the running state, and the OHCI
controller would then raise an unrecoverableError interrupt because the
first Z value is zero and thus invalid. The driver logs such errors,
but there is no mechanism to report this back to the program.
Add an explicit check so that this error can be returned synchronously.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
To prevent the iso packet callback from being called after
fw_iso_context_stop() has returned, make sure that the
context's tasklet has finished executing before that.
This fixes access-after-free bugs that have so far been
observed only in the upcoming snd-firewire-speakers driver,
but can theoretically also happen in the firedtv driver.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
In manage_channel(), rename the variables "c" and "i" to the more
expressive "bit" and "channel".
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
The first board generation of Power Mac G4 ("Yikes!", those with PCI
graphics) still had a PCILynx controller like their G3 predecessors,
but not the later AGP models. (Jonathan Woithe recalls to have heard
of it, and some web sources reinforce it.)
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
On a 32-bit machine with, e.g., HZ=1000, jiffies will overflow after
about 50 days, so if there are between 25 and 50 days between bus
resets, the card->reset_jiffies comparisons can get wrong results.
To fix this, ensure that this timestamp always uses 64 bits.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: "Stefan Richter" <stefanr@s5r6.in-berlin.de>
For outbound transactions, the IDR's and the callback's references now
have exactly the same lifetime, so we do not need both of them.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: "Stefan Richter" <stefanr@s5r6.in-berlin.de>
We must not use fw_cancel_transaction() because it cannot correctly
abort still-active transactions. The only place in core-cdev where this
matters is when the file is released. Instead of trying to abort the
transactions, we wait for them to complete normally, i.e., until all
outbound transaction resources have been removed from the IDR tree.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: "Stefan Richter" <stefanr@s5r6.in-berlin.de>
Outbound transactions are never aborted with release_client_resource(),
so it is not necessary for complete_transaction() to check whether the
resource is still registered. Only shutdown_resource() can abort such
an transaction, and this is already handled with the in_shutdown check.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: "Stefan Richter" <stefanr@s5r6.in-berlin.de>
When a DMA context goes into the dead state (and the controller thus
stops working correctly), logging this error and the controller's error
code might be helpful for debugging.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
firewire: core: fix unstable I/O with Canon camcorder
* 'fwnet' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
firewire: net: is not experimental anymore
firewire: net: invalidate ARP entries of removed nodes
thanks to Clemens' and Maxim's fixes to firewire-ohci and -net in the
last two kernel releases.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
This makes it possible to resume communication with a node that dropped
off the bus for a brief period. Otherwise communication will only be
possible after ARP cache entry timeouts.
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (rebased)
Regression since commit 1038953674, "firewire: core: check for 1394a
compliant IRM, fix inaccessibility of Sony camcorder":
The camcorder Canon MV5i generates lots of bus resets when asynchronous
requests are sent to it (e.g. Config ROM read requests or FCP Command
write requests) if the camcorder is not root node. This causes drop-
outs in videos or makes the camcorder entirely inaccessible.
https://bugzilla.redhat.com/show_bug.cgi?id=633260
Fix this by allowing any Canon device, even if it is a pre-1394a IRM
like MV5i are, to remain root node (if it is at least Cycle Master
capable). With the FireWire controller cards that I tested, MV5i always
becomes root node when plugged in and left to its own devices.
Reported-by: Ralf Lange
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: <stable@kernel.org> # 2.6.32.y and newer
PAGE_KERNEL_RO is not available on all architectures, so its use
in the new AR code broke compilation on sparc64.
Because the read-only mapping was just a debugging aid, just use
PAGE_KERNEL instead.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
James Bottomley wrote:
> On Thu, 2011-01-13 at 08:27 +0100, Clemens Ladisch wrote:
>> firewire: ohci: fix compilation on arches without PAGE_KERNEL_RO, e.g. sparc
>>
>> PAGE_KERNEL_RO is not available on all architectures, so its use in the
>> new AR code broke compilation on sparc64.
>>
>> Because the R/O mapping is only used to catch drivers that try to write
>> to the reception buffer and not actually required for correct operation,
>> we can just use a normal PAGE_KERNEL mapping where _RO is not available.
[...]
>> +/*
>> + * For archs where PAGE_KERNEL_RO is not supported;
>> + * mapping the AR buffers readonly for the CPU is just a debugging aid.
>> + */
>> +#ifndef PAGE_KERNEL_RO
>> +#define PAGE_KERNEL_RO PAGE_KERNEL
>> +#endif
>
> This might cause interesting issues on sparc64 if it ever acquired a
> PAGE_KERNEL_RO. Sparc64 has extern pgprot_t for it's PAGE_KERNEL types
> rather than #defines, so the #ifdef check wouldn't see this.
>
> I think either PAGE_PROT_RO becomes part of our arch API (so all
> architectures are forced to add it), or, if it's not part of the API,
> ohci isn't entitled to use it. The latter seems simplest since you have
> no real use for write protection anyway.
Reported-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Instead of starting the split transaction timeout timer when any request
is submitted, start it only when the destination's ACK_PENDING has been
received. This prevents us from using a timeout that is too short, and,
if the controller's AT queue is emptying very slowly, from cancelling
a packet that has not yet been sent.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
"firewire: ohci: restart iso DMA contexts on resume from low power mode"
added the flag struct context.active and "firewire: ohci: cache the
context run bit" added struct context.running.
These flags contain the same information; combine them.
Also, normalize whitespace in pci_resume().
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
The DMA context run control bit is entirely controlled by software, so
it is safe to cache it. This allows the driver to avoid doing an
additional MMIO read when queueing an AT packet.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Add comments
- on why bus_reset_tasklet flushes AT queues,
- that commit 76f73ca1b2 can possibly be reverted now.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Acked-by: Jarod Wilson <jarod@redhat.com>
The OHCI 1.2 (draft) specification, clause 7.2.3.3, allows and
recommends that, after a bus reset, the controller does not flush all
the packets in the AT queues. Therefore, the driver has to do this
itself.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
At ifup, carrier status would be shown on even if it actually was off.
Also add an include for ethtool_ops rather than to rely on the one from
netdevice.h.
Note, we can alas not use fwnet_device_mutex to serialize access to
dev->peer_count (as I originally wanted). This would cause a lock
inversion:
- fwnet_probe | takes fwnet_device_mutex
+ register_netdev | takes rtnl_mutex
- devinet_ioctl | takes rtnl_mutex
+ fwnet_open | ...must not take fwnet_device_mutex
Hence use the dev->lock spinlock for serialization.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
