This was removed in the libgcc integration, but there are still some
compilers that need this. We also relax the rules on the ISA tuning in
the cases where there are no matches for the CPU tuning and adopt the
-any default, which matches the intent of the isa-y target list. This
compensates for mismatches where binutils supports a wide array of
targets whilst the compiler is much more restricted.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds support for unaligned loads on SH-4A, using the SH-4A's
neutered movua.l instruction. As movua.l is r0-inspired, stores are
still handled through the packed struct.
Based on asm-generic/unaligned.h by Harvey Harrison.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds a pass-through case when ioremapping P4 addresses.
Addresses passed to ioremap() should be physical addresses, so the
best option is usually to convert the virtual address to a physical
address before calling ioremap. This will give you a virtual address
in P2 which matches the physical address and this works well for
most internal hardware blocks on the SuperH architecture.
However, some hardware blocks must be accessed through P4. Converting
the P4 address to a physical and then back to a P2 does not work. One
example of this is the sh7722 TMU block, it must be accessed through P4.
Without this patch P4 addresses will be mapped using PTEs which
requires the page allocator to be up and running.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add fast mutex path implementation for the SH4A architecture
Signed-off-by: Michael Trimarchi <trimarchimichael@yahoo.it>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The SH7709 datasheet defines bit 5 as set for burst mode, clear for
cycle-steal mode.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
sh7709 hardware manual says DMAOR is 16 bits long on this platform.
Tested and working with a modified smsc911x ethernet driver (sh-dma
support patch for this driver is coming soon).
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
I'm using these constants in support of an in-house development board,
and thought they may be useful to other users of SH7709.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This moves in the necessary libgcc bits for SUPERH32 and drops the
libgcc linking for the regular targets. This in turn allows us to rip
out quite a few hacks both in sh_ksyms_32 and arch/sh/Makefile.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
CC arch/sh/kernel/cpu/clock.o
arch/sh/kernel/cpu/clock.c: In function 'clk_disable':
arch/sh/kernel/cpu/clock.c:156: warning: 'return' with a value, in function returning void
Introduced by ("sh: enable and disable clocks recursively").
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add clock framework support to the lcdc driver and
adjust the board specific code accordingly.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add clock framework support to the usb/r8a66597 driver and
adjust the cpu specific code accordingly.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add clock framework support to the usbf/m66592 driver and
adjust the cpu specific code accordingly.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add clock framework support to the sh_mobile ceu and
adjust the board specific code accordingly.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add clock framework support to the sh_mobile keysc driver and
adjust the board specific code accordingly.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add clock framework support to the sh_mobile i2c driver and
adjust the processor specific code accordingly.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add sh7366 mstpcr bits and information about their parent clocks.
The datasheet is pretty clear about the clocks on this device.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add sh7343 mstpcr bits and information about their parent clocks.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add sh7723 mstpcr bits and information about their parent clocks.
The datasheet is pretty clear about the clocks on this device.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add sh7722 mstpcr bits and information about their parent clocks.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add base code to handle new mstpcr clocks. Make sure clock rates propagate.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Presently limited to Cayman, Dreamcast, Microdev, and SystemH 7751.
Re-enable it for everyone once these have been fixed up.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Impact: change calling convention of existing clock_event APIs
struct clock_event_timer's cpumask field gets changed to take pointer,
as does the ->broadcast function.
Another single-patch change. For safety, we BUG_ON() in
clockevents_register_device() if it's not set.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Ingo Molnar <mingo@elte.hu>
Impact: cleanup
Each SMP arch defines these themselves. Move them to a central
location.
Twists:
1) Some archs (m32, parisc, s390) set possible_map to all 1, so we add a
CONFIG_INIT_ALL_POSSIBLE for this rather than break them.
2) mips and sparc32 '#define cpu_possible_map phys_cpu_present_map'.
Those archs simply have phys_cpu_present_map replaced everywhere.
3) Alpha defined cpu_possible_map to cpu_present_map; this is tricky
so I just manipulate them both in sync.
4) IA64, cris and m32r have gratuitous 'extern cpumask_t cpu_possible_map'
declarations.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Reviewed-by: Grant Grundler <grundler@parisc-linux.org>
Tested-by: Tony Luck <tony.luck@intel.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: Mike Travis <travis@sgi.com>
Cc: ink@jurassic.park.msu.ru
Cc: rmk@arm.linux.org.uk
Cc: starvik@axis.com
Cc: tony.luck@intel.com
Cc: takata@linux-m32r.org
Cc: ralf@linux-mips.org
Cc: grundler@parisc-linux.org
Cc: paulus@samba.org
Cc: schwidefsky@de.ibm.com
Cc: lethal@linux-sh.org
Cc: wli@holomorphy.com
Cc: davem@davemloft.net
Cc: jdike@addtoit.com
Cc: mingo@redhat.com
Mathieu Desnoyers reported this build failure on powerpc:
kernel/sched.c: In function 'sd_init_NODE':
kernel/sched.c:7319: error: non-static initialization of a flexible array member
kernel/sched.c:7319: error: (near initialization for '(anonymous)')
this happens because .span changed to cpumask_var_t, hence
the static CPU_MASK_NONE initializers in the SD_*_INIT
templates are not type-correct anymore.
Remove them, as they default to empty anyway.
Also remove them from IA64, MIPS and SH.
Reported-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Under qemu there is a race between the TDxE read-and-clear and the SCxTDR
write. While on hardware it can be gauranteed that the read-and-clear
will happen prior to the character being written out, no such assumption
can be made under emulation. As this path happens with IRQs off and the
hardware itself doesn't care about the ordering, move the SCxTDR write
until after the read-and-clear.
Signed-off-by: Vladimir Prus <vladimir@codesourcery.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The __copy_user function can corrupt the stack in the case of a
non-trivial length of data, and either of the first two move instructions
cause an exception. This is because the fixup for these two instructions
is mapped to the no_pop case, but these instructions execute after the
stack is pushed.
This change creates an explicit NO_POP exception mapping macro, and uses
it for the two instructions executed in the trivial case where no stack
pushes occur.
More information at ST Linux bugzilla:
https://bugzilla.stlinux.com/show_bug.cgi?id=4824
Signed-off-by: Dylan Reid <dylan_reid@bose.com>
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch fixes the TMU0 interrupt frequency on suspend/resume.
During the resume the kernel reprograms the TMU0.ClockEvent mode
but if the mode is periodic than the TMU0.TCOR is updated with
a random wrong value without taking care latest valid saved value.
There was no problem with No_HZ system where TMU0.TCOR isn't used.
Signed-off-by: Francesco M. Virlinzi <francesco.virlinzi@st.com>
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
With the PMB enabled, only P1SEG and up are covered by the PMB mappings,
meaning that situations where out-of-bounds physical addresses are read
from will lead to TLB reset after the PMB miss, allowing for use cases
like dd if=/dev/mem to reset the TLB.
Fix this up to make sure the reference is between __MEMORY_START (phys)
and __pa(high_memory). This is coherent across all variants of sh/sh64
with and without MMU, though the PMB bug itself is only applicable to
SH-4A parts.
Reported-by: Hideo Saito <saito@densan.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch changes sci type of SH7723 from PORT_SCI to PORT_SCIFA.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
There was a race in the kmap_coherent() implementation. While we
guarded against preemption, there was nothing preventing eviction of
the pre-faulted fixmap entry from the UTLB. Under certain workloads
this would result in the fixmap entries used for cache colouring being
evicted from the UTLB in the midst of a copy_page().
In addition to pre-faulting, we also make sure to preserve the PTEs
in the kernel page table and introduce a cached PTE for kmap_coherent()
usage. This follows a similar change on MIPS ("[MIPS] Fix aliasing bug
in copy_to_user_page / copy_from_user_page").
Reported-by: Hideo Saito <saito@densan.co.jp>
Reported-by: CHIKAMA Masaki <masaki.chikama@gmail.com>
Tested-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch add usb setting for sh 7366
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
SH-5 doesn't support any elaborate ISA inheritance schemes (-dsp, -up,
etc.), so only bother with that if we are building an sh32 kernel.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This code has been dead for many years. The last update it received
was in 2003 in order to update it for the driver model changes, though
it had already been in disarray and unused before that point. The only
boards that ever used this chip have not had users in many years either,
so it is finally safe to just kill it off and move on with life.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The ISA tuning as it is today can not cope with all of the different
variations that are possible, so all we can do is a best attempt based on
the CPU family. The DSP and FPU generation are already at odds with each
other, and the nommu tuning we weren't handling at all. Additionally,
for platforms that never had an FPU, the -nofpu variant never existed,
meaning that we would lose out on family granular tuning completely in
certain cases.
With tat out of the way, we were also using -up versions, allowing for
later instructions that branched off of a particular subset of the ISA,
but are not actually reflected on the hardware being targetted. This
leads to some confusion, and the possibility of bogus instructions on
older parts. Kill that off and lock it down to the family being built
for specifically.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Presently there is very little standing in the way of using an SH-4
toolchain for building an SH-2 kernel, and vice versa. Binutils itself
has no limitations whatsoever and supports explicit ISA hinting, which
we already use with varying degrees of success today.
This leaves GCC as the odd one out, due to a rather dubious policy
decision by the GCC folks to not include all of the CPU family variants
in the default list of multilib targets in GCC4. Despite best efforts to
the contrary, libgcc itself already contains awareness of the various CPU
types and remains generally usable, allowing it to safely be referenced
even on a mismatched target (and indeed, explicit ISA tuning by binutils
keeps us honest in terms of ensuring that we do not link incompatible
objects in).
In order to support this, a couple of changes had to be made. Firstly,
the introduction of MAYBE_DECLARE_EXPORT(), which provides a __weak
extern reference for libgcc resident routines when finer-grained
-m<cpu-family> based tuning is not supported by the toolchain. This
fixes up the __sdivsi3_i4i and __udivsi3_i4i references when dealing
with SH-2 kernels linked with an SH-4 libgcc. Secondly, in case where we
are unable to find a suitable match for CPU family tuning but still
have a toolchain that defaults to FP instruction generation, a suitable
nofpu target must be selected. This is accomplished by selecting the
first nofpu multilib target supported by the toolchain, which is
also necessary for selecting the proper libgcc to link against.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Rather than varying this on a subtype level, we use the counter type as a
generic identifier. This simplifies logic in the userspace tools where no
fundamental difference exists across the various subtypes.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch implements pinmux tables for the sh7785 processor.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch improves the support for gpio pins that are hard wired
to either input or output and lack control register association.
A special force enum id is used to allow use without control
register but still mark the gpio pin as input or output.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Use a slower VIO_CKO clock frequency for the ov772x on Migo-R.
This improves the camera picture quality on Panel Board V2.1.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch updates the pinmux code to use the boolean value for
the function gpio_set_value(). Without this patch values other
than 0 and 1 will result in incorrect GPIO settings.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Update the ov772x byte sequence to enable byte swap. This to reflect
the recent CEU driver change to follow incoming byte order.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Commit 3f5a54e371 ("ftrace: dump out ftrace
buffers to console on panic") added an ftrace buffer dumper that hooks
in to the die notifier chain and dumps out data in the oops path.
Unfortunately SH supported ftrace but didn't support DIE_OOPS, so add
that in and get it building again.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Use the generic remove_memory() provided by mm/memory_hotplug.c instead.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The sh7203.h include paths were missed in the previous update, so switch
the include path to cpu/ as with the rest.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (112 commits)
sh: Move SH-4 CPU headers down one more level.
sh: Only build in gpio.o when CONFIG_GENERIC_GPIO is selected.
sh: Migrate common board headers to mach-common/.
sh: Move the CPU definition headers from asm/ to cpu/.
serial: sh-sci: Add support SCIF of SH7723
video: add sh_mobile_lcdc platform flags
video: remove unused sh_mobile_lcdc platform data
sh: remove consistent alloc cruft
sh: add dynamic crash base address support
sh: reduce Migo-R smc91x overruns
sh: Fix up some merge damage.
Fix debugfs_create_file's error checking method for arch/sh/mm/
Fix debugfs_create_dir's error checking method for arch/sh/kernel/
sh: ap325rxa: Add support RTC RX-8564LC in AP325RXA board
sh: Use sh7720 GPIO on magicpanelr2 board
sh: Add sh7720 pinmux code
sh: Use sh7203 GPIO on rsk7203 board
sh: Add sh7203 pinmux code
sh: Use sh7723 GPIO on AP325RXA board
sh: Add sh7723 pinmux code
...
o elfcorehdr_addr is used by not only the code under CONFIG_PROC_VMCORE
but also by the code which is not inside CONFIG_PROC_VMCORE. For
example, is_kdump_kernel() is used by powerpc code to determine if
kernel is booting after a panic then use previous kernel's TCE table.
So even if CONFIG_PROC_VMCORE is not set in second kernel, one should be
able to correctly determine that we are booting after a panic and setup
calgary iommu accordingly.
o So remove the assumption that elfcorehdr_addr is under
CONFIG_PROC_VMCORE.
o Move definition of elfcorehdr_addr to arch dependent crash files.
(Unfortunately crash dump does not have an arch independent file
otherwise that would have been the best place).
o kexec.c is not the right place as one can Have CRASH_DUMP enabled in
second kernel without KEXEC being enabled.
o I don't see sh setup code parsing the command line for
elfcorehdr_addr. I am wondering how does vmcore interface work on sh.
Anyway, I am atleast defining elfcoredhr_addr so that compilation is not
broken on sh.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: Simon Horman <horms@verge.net.au>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch implements a new freezer subsystem in the control groups
framework. It provides a way to stop and resume execution of all tasks in
a cgroup by writing in the cgroup filesystem.
The freezer subsystem in the container filesystem defines a file named
freezer.state. Writing "FROZEN" to the state file will freeze all tasks
in the cgroup. Subsequently writing "RUNNING" will unfreeze the tasks in
the cgroup. Reading will return the current state.
* Examples of usage :
# mkdir /containers/freezer
# mount -t cgroup -ofreezer freezer /containers
# mkdir /containers/0
# echo $some_pid > /containers/0/tasks
to get status of the freezer subsystem :
# cat /containers/0/freezer.state
RUNNING
to freeze all tasks in the container :
# echo FROZEN > /containers/0/freezer.state
# cat /containers/0/freezer.state
FREEZING
# cat /containers/0/freezer.state
FROZEN
to unfreeze all tasks in the container :
# echo RUNNING > /containers/0/freezer.state
# cat /containers/0/freezer.state
RUNNING
This is the basic mechanism which should do the right thing for user space
task in a simple scenario.
It's important to note that freezing can be incomplete. In that case we
return EBUSY. This means that some tasks in the cgroup are busy doing
something that prevents us from completely freezing the cgroup at this
time. After EBUSY, the cgroup will remain partially frozen -- reflected
by freezer.state reporting "FREEZING" when read. The state will remain
"FREEZING" until one of these things happens:
1) Userspace cancels the freezing operation by writing "RUNNING" to
the freezer.state file
2) Userspace retries the freezing operation by writing "FROZEN" to
the freezer.state file (writing "FREEZING" is not legal
and returns EIO)
3) The tasks that blocked the cgroup from entering the "FROZEN"
state disappear from the cgroup's set of tasks.
[akpm@linux-foundation.org: coding-style fixes]
[akpm@linux-foundation.org: export thaw_process]
Signed-off-by: Cedric Le Goater <clg@fr.ibm.com>
Signed-off-by: Matt Helsley <matthltc@us.ibm.com>
Acked-by: Serge E. Hallyn <serue@us.ibm.com>
Tested-by: Matt Helsley <matthltc@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The pinmux management is tied in to this code, while it is presently only
used by platforms that select GENERIC_GPIO. The asm/gpio.h definitions
are not referenced when GENERIC_GPIO is disabled, resulting in a build
failure for all of the platforms that don't select it.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Remove left overs from the generic declared coherent rework.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Improve Migo-R ethernet performance by reducing smc91x overruns.
This is done by enabling SMC91X_NOWAIT and optimizing CS4 setup.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
debugfs_create_file() returns NULL if an error occurs, returns -ENODEV
when debugfs is not enabled in the kernel.
Signed-off-by: Zhao Lei <zhaolei@cn.fujitsu.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
debugfs_create_dir() returns NULL if an error occurs, returns -ENODEV
when debugfs is not enabled in the kernel.
Signed-off-by: Zhao Lei <zhaolei@cn.fujitsu.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Renesas AP325RXA board has Epson RX-8564LC of RTC.
This patch supports RTC of this board.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch hooks up the magicpanelr2 board with the sh7720 pinmux code.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds pinmux and gpio support for the sh7720 processor.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Make the rsk7203 board use the newly added sh7203 pinmux code.
Only a single LED plus the serial console pins for now.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds pinmux and gpio support for the sh7203 processor.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch enables the GPIO code on AP325RXA and converts the code from
register based pinmux configuration to GPIO based pin by pin setup.
While at it 2 LEDs and one switch are added and exported to user space.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds pinmux and gpio support for the sh7723 processor.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch enables the GPIO code on Migo-R and converts the code from
register based pinmux configuration to GPIO based pin by pin setup.
Fix whitespace damage while at it and add 2 LEDs and export them to
user space.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds pinmux and gpio support for the sh7722 processor.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds gpio code together with the pinmux table parser.
In the future we should optimize this and switch back to gpiolib.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The SET_PERSONALITY macro is always called with a second argument of 0.
Remove the ibcs argument and the various tests to set the PER_SVR4
personality.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This tidies up a lot of the PIO/MMIO split. No in-tree platforms were
making use of the MMIO overloading through the machvec (nor have any of
them been in some time), so we just kill all of that off. The ISA I/O
routine wrapping remains unaffected, which remains the only special
casing outside of the iomap API that boards need to think about.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This provides a workaround for users of sh_mobile_lcdcfb that don't
define HAVE_CLK and have otherwise sane clock initialization.
At the same time, move the sh_mobile_lcdc.h header to include/video/.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The INTC code will be re-used across different architectures, so move
this out to drivers/sh/ and include/linux/sh_intc.h respectively.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
These were doing largely bogus things and using the wrong typing for
the address. Bring these in line with the ARM definitions.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
AP320 and AP325RXA has CPLD data in NOR Flash.
If this area erased, this board can not boot.
This patch create CPLD data area and set writeable mask bit.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds support for ftrace to SH. This only includes CONFIG_FTRACE,
and does not handle dynamic ftrace presently.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This implements a few trace points across events that are deemed
interesting. This implements a number of trace points:
- The page fault handler / TLB miss
- IPC calls
- Kernel thread creation
The original LTTng patch had the slow-path instrumented, which
fails to account for the vast majority of events. In general
placing this in the fast-path is not a huge performance hit, as
we don't take page faults for kernel addresses.
The other bits of interest are some of the other trap handlers, as
well as the syscall entry/exit (which is better off being handled
through the tracehook API). Most of the other trap handlers are corner
cases where alternate means of notification exist, so there is little
value in placing extra trace points in these locations.
Based on top of the points provided both by the LTTng instrumentation
patch as well as the patch shipping in the ST-Linux tree, albeit in a
stripped down form.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
There are other places where we want to have access to the trap/exception
number, so move out the lookup_exception_vector() helper. While we're at
it, refactor it slightly to return the vector instead.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This is 256K instead of 1M.
[ Converted to use asm/sizes.h. -- PFM ]
Signed-off-by: Luca Santini <luca.santini@spesonline.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This follows the powerpc commit f6a616800e
'[POWERPC] Fix kernel stack allocation alignment'.
SH has traditionally forced the thread order to be relative to the page
size, so there were never any situations where the same bug was
triggered by slub. Regardless, the usage of > 8kB stacks for the larger
page sizes is overkill, so we switch to using slab allocations there,
as per the powerpc change.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This combination triggers a divide by zero in kernel/fork.c when
calculating the initial max_threads value:
max_threads = mempages / (8 * THREAD_SIZE / PAGE_SIZE);
Simply disable 4K stacks on 64kB PAGE_SIZE to work around this,
as it's not a terribly useful combination to begin with.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
HAVE_IOREMAP_PROT enables an unconditional reference to
generic_access_phys(), which remains undefined in the nommu case.
As there's no point in supporting this there anyways, simply fix
up the dependency.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
linux/mmzone.h isn't exported, kill it off from asm/setup.h and simply
deal with it in the places that have a dependency instead.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
These have been using overrides for ELF_CORE_COPY_TASK_REGS and
ELF_CORE_COPY_FPREGS while the generic versions can be used instead.
Presently the pt_regs are also duplicated across elf_core_copy_regs()
and elf_core_copy_task_regs(), this switches to simply copying out
through elf_core_copy_regs() instead.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now that the rest of the support requirements are out of the way, finally
enable support for tracehook.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
