* get_rate_arm : when 400MHz clock is selected (cctl & 1<<14),
ARM clock is 400MHz (MPLL * 3 / 4) and not 800MHz
* get_rate_per : peripherals's clock is derived from AHB and not
from IPG (ref manual : figure 5-1)
* can2_clk : use the correct ID
* without this patch, peripherals getting their clock from PER
clocks work fine because of the 2 errors which fix themselves
(ARM clock x 2 and per clock actually based on IPG which is AHB/2)
but flexcan can't work as it gets its clock from IPG and thus
calculates its bitrate using a reference value which is twice
what it really is.
Signed-off-by: Eric Bénard <eric@eukrea.com>
During the reorganisation of the imx-i2c devices
(in 64de5ec168) the 3rd imx-i2c device
for the mx35 got lost. This patch adds the missing device.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add IRAM(Internal RAM) allocation functions using GENERIC_ALLOCATOR.
The allocation size is 4KB multiples to guarantee alignment. The
idea for these functions is for i.MX platforms to use them
to dynamically allocate IRAM usage.
Applies on 2.6.36-rc7
Signed-off-by: Dinh Nguyen <Dinh.Nguyen@freescale.com>
Reviewed-by: Amit Kucheria <amit.kucheria@canonical.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The i.MX51 ECSPI has a fifo size of 64 entries instead of 8 entries as
found on the other cspi bus devices.
Cc: Jason Wang <jason77.wang@gmail.com>
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
So the correct clock will be taken for each of the two independent
controllers.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Documentation/gpio.txt specifies that the value argument to
gpio_set_value() should be handled as a boolean (E.G. != 0 is high),
so use the same logic as in _set_direction().
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
i.MX35 CPUs marked with "MCIMX357CJQ5C M99V CTHA0943B" are coming with bogus
L2 cache settings. If these settings are kept unmodified prior enabling the L2
cache the CPU runs amok immediately when its enabled.
This fix should not hurt already working CPUs, as they are using the written
register value already.
Its currently unknown if its possible to detect the production lot from the
software to fix only affected CPUs.
While at it, make sure that mxc_init_l2x0 is only executed on i.MX31/35
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This fixes
arch/arm/mach-mx3/mach-cpuimx35.c:143: warning: 'otg_pdata' defined but not used
arch/arm/mach-mx3/mach-cpuimx35.c:148: warning: 'usbh1_pdata' defined but not used
when USB_ULPI is not selected.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Based on work done earlier by Sascha Hauer
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Eric Bénard <eric@eukrea.com>
[ukl: actually squash the two approaches together]
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
- remove functions which are no more necessary for tsc2007
- indent platform_data for better readability
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The first argument to I2C_BOARD_INFO is used to assign .type, so it should
not be specified a second time.
For the rtc-pcf8563/pcf8563 entry gcc preferred pcf8563, so did I.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This fixes the following sparse warning:
arch/arm/mach-imx/pcm970-baseboard.c:224:13: warning: symbol 'pcm970_baseboard_init' was not declared. Should it be static?
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This fixes the following sparse warning:
arch/arm/mach-imx/pcm970-baseboard.c:203:30: warning: symbol 'pcm970_sja1000_platform_data' was not declared. Should it be static?
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Currently the uarts and timer only work because they are
turned on by reset default. Make them secondary clocks
of their corresponding peripheral clocks to make sure they
are turned on when necessary. Also, register some clocks
to get rid of compiler warnings
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Addiontionally make the interrupt #defines match the base address
defines MX.._NFC_BASE_ADDR.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
A 2M bytes SPI NOR flash(sst25vf016b) is soldered on the mx51_3ds
board. So add the corresponding device for it.
Signed-off-by: Jason Wang <jason77.wang@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
On the imx51_3ds board, eCSPI2 is connected to a SPI NOR flash,
now add iomux definitions for those used pins.
Signed-off-by: Jason Wang <jason77.wang@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The driver recently learned to handle platform ids. Make use of this
new feature. The up side is that the driver needs less knowledge about
the spi interfaces used on different SoCs.
Acked-by: Jason Wang <jason77.wang@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
i.MX51 comes with two eCSPI interfaces (that are quite different from
what was known before---the tried and tested Freescale way) and a CSPI
interface that is identical to the devices found on i.MX25 and i.MX35.
This patch is a merge of two very similar patches (by Jason Wang and Sascha
Hauer resp.) plus a (now hopefully correct) reimplementation of the
clock calculation.
Acked-by: Jason Wang <jason77.wang@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This prepares adding support for imx51's eCSPI. This IP has seperate
control and config bits for all four supported chip selects, so the
config routine needs to know which chip select is being used even if
the chipselect is realized by a gpio.
Acked-by: Jason Wang <jason77.wang@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Nearly everything that is needed is provided by the version of the SPI IP.
Now the only checks left using cpu_is_... are clk divider tuning on mx21/mx27
and autodetection (which will die soon).
Acked-by: Jason Wang <jason77.wang@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This has the advantage not to need to much cpu_is_... macros. Still more
when imx51 support is added which has two different spi interfaces which
would introduce additional checks on the device id.
With this setup it's not possible for the compiler anymore to detect the
unused functions, so four additional kconfig symbols are introduced to
ifdef out the unneeded functions in the callback array and all these
functions are marked with __maybe_unused to suppress the corresponding
gcc warnings.
Comparing the driver footprint with and without the patch for a mx27
kernel yields:
add/remove: 2/0 grow/shrink: 2/0 up/down: 280/0 (280)
function old new delta
spi_imx_devtype - 192 +192
spi_imx_probe 980 1032 +52
spi_imx_devtype_data - 32 +32
spi_imx_setupxfer 276 280 +4
Later when the platform code is updated to use the platform ids, the
autodetection can be removed which will make the driver a bit smaller
again. (~60 Bytes in my test.)
Acked-by: Jason Wang <jason77.wang@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
